Tomigolung, Lucky Jack Arthur (2026) ANALISIS PENGARUH TRIMMING IMPELLER 15% TERHADAP EFISIENSI ENERGI DAN KARAKTERISTIK OPERASIONAL POMPA SENTRIFUGAL CRUDE OIL DI ANJUNGAN LEPAS PANTAI. S1 thesis, Universitas Kristen Indonesia.
|
Text (Hal_Judul_Daftar_Isi_Abstrak)
HalJudulDaftarIsiAbstrak.pdf Available under License Creative Commons Attribution Non-commercial Share Alike. Download (1MB) |
|
|
Text (BAB_I)
BABI.pdf Available under License Creative Commons Attribution Non-commercial Share Alike. Download (479kB) |
|
|
Text (BAB_II)
BABII.pdf Restricted to Registered users only Available under License Creative Commons Attribution Non-commercial Share Alike. Download (883kB) |
|
|
Text (BAB_III)
BABIII.pdf Restricted to Registered users only Available under License Creative Commons Attribution Non-commercial Share Alike. Download (995kB) |
|
|
Text (BAB_IV)
BABIV.pdf Restricted to Registered users only Available under License Creative Commons Attribution Non-commercial Share Alike. Download (1MB) |
|
|
Text (BAB_V)
BABV.pdf Restricted to Registered users only Available under License Creative Commons Attribution Non-commercial Share Alike. Download (549kB) |
|
|
Text (Daftar_Pustaka)
DaftarPustaka.pdf Available under License Creative Commons Attribution Non-commercial Share Alike. Download (385kB) |
|
|
Text (Lampiran)
Lampiran.pdf Restricted to Registered users only Available under License Creative Commons Attribution Non-commercial Share Alike. Download (1MB) |
Abstract
Pompa sentrifugal di anjungan lepas pantai sering mengalami oversizing akibat desain dengan safety factor yang tinggi, menyebabkan pompa beroperasi jauh dari Best Efficiency Point (BEP) dan memerlukan throttling berlebihan yang engakibatkan pemborosan energi serta penurunan keandalan. Penelitian ini bertujuan menganalisis pengaruh trimming impeller sebesar 15% (dari diameter 11,75 inci menjadi 10 inci) terhadap efisiensi energi, keandalan, kapasitas aliran, head pompa, perilaku sistem kontrol, serta memvalidasi hukum afinitas pada pompa sentrifugal crude oil di Anjungan X. Penelitian menggunakan pendekatan studi kasus kuantitatif dengan metode komparatif, menggunakan data operasional dari log sheet dan sistem DCS periode Januari 2023 hingga Maret 2026 yang terbagi menjadi periode sebelum trimming (14 bulan), periode transisi (11 bulan), dan setelah trimming stabil (13 bulan). Parameter yang dianalisis meliputi arus motor, kecepatan vibrasi, temperatur, laju alir, tekanan discharge, head pompa, dan perilaku valve recycle. Hasil penelitian menunjukkan bahwa trimming impeller 15% berhasil menurunkan konsumsi arus motor sebesar 33,8% (dari 32,0 A menjadi 21,2 A) setara dengan penghematan daya 7,6 kW atau biaya listrik sekitar Rp99.864.000 per tahun. Kecepatan vibrasi menurun 39,2% (dari 2,22 mm/s menjadi 1,35 mm/s), temperatur fluida turun 20,5% (dari 58,5°C menjadi 46,5°C), dan laju alir mengalami penurunan terbatas sebesar 13,6% (dari 28.723 BFPD menjadi 24.826 BFPD). Head pompa menurun 34,2% (dari 597,4 ft menjadi 393,0 ft) dan tekanan discharge menurun 32,1% (dari 240 PSI menjadi 163 PSI). Terjadi perubahan fundamental pada sistem kontrol dengan penurunan bukaan LIC Recycle dari rata-rata 50% menjadi 32%. Hukum afinitas menunjukkan akurasi yang bervariasi dengan deviasi 1,5% untuk laju alir, 9,1% untuk head, dan 7,6% untuk daya. Pompa telah beroperasi lebih dari 2 tahun pasca-trimming dengan total 18.112 jam tanpa mengalami kerusakan. Komparasi dengan pompa baru dan alternatif trimming 20% menunjukkan bahwa trimming 15% merupakan solusi paling optimal dengan risiko rendah dan payback period kurang dari 1 tahun. Kesimpulannya, trimming impeller 15% terbukti efektif mengatasi masalah oversize pada pompa sentrifugal crude oil di lingkungan offshore, memberikan manfaat ganda berupa penghematan energi signifikan dan peningkatan keandalan, sehingga direkomendasikan sebagai solusi low-cost retrofit untuk pompa oversize dengan kebutuhan laju alir yang relatif konstan. / Centrifugal pumps on offshore platforms often experience oversizing due to designs with high safety factors, causing the pumps to operate far from the Best Efficiency Point (BEP) and requiring excessive throttling, which results in energy waste and reduced reliability. This study aims to analyze the effect of a 15% impeller trimming (from a diameter of 11.75 inches to 10 inches) on energy efficiency, reliability, flow capacity, pump head, control system behavior, and to validate the affinity laws on a crude oil centrifugal pump at Platform X. The study uses a quantitative case study approach with a comparative method, utilizing operational data from log sheets and the DCS system for the period from January 2023 to March 2026, divided into the pre-trimming period (14 months), transition period (11 months), and stable post-trimming period (13 months). The parameters analyzed include motor current, vibration velocity, temperature, flow rate, discharge pressure, pump head, and recycle valve behavior. The results show that a 15% impeller trimming successfully reduced motor current consumption by 33.8% (from 32.0 A to 21.2 A), equivalent to power savings of 7.6 kW or electricity cost savings of approximately IDR 99,864,000 per year. Vibration velocity decreased by 39.2% (from 2.22 mm/s to 1.35 mm/s), fluid temperature dropped by 20.5% (from 58.5°C to 46.5°C), and the flow rate experienced a limited decrease of 13.6% (from 28,723 BFPD to 24,826 BFPD). Pump head decreased by 34.2% (from 597.4 ft to 393.0 ft) and discharge pressure decreased by 32.1% (from 240 PSI to 163 PSI). A fundamental change occurred in the control system with a decrease in LIC Recycle opening from an average of 50% to 32%. The affinity laws showed varying accuracy with deviations of 1.5% for flow rate, 9.1% for head, and 7.6% for power. The pump has been operating for more than 2 years post-trimming with a total of 18,112 hours without experiencing any damage. Comparison with a new pump and an alternative 20% trimming shows that 15% trimming is the most optimal solution with low risk and a payback period of less than 1 year. In conclusion, 15% impeller trimming is proven effective in overcoming the oversize problem of crude oil centrifugal pumps in offshore environments, providing dual benefits in the form of significant energy savings and increased reliability, thus recommended as a low-cost retrofit solution for oversize pumps with relatively constant flow rate requirements.
| Item Type: | Thesis (S1) | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Contributors: |
|
||||||||||||
| Subjects: | TECHNOLOGY > Mechanical engineering and machinery | ||||||||||||
| Divisions: | FAKULTAS TEKNIK > Teknik Mesin | ||||||||||||
| Depositing User: | Mr Lucky Jack Arthur Tomigolung | ||||||||||||
| Date Deposited: | 08 Nov 2026 03:27 | ||||||||||||
| Last Modified: | 08 Nov 2026 03:27 | ||||||||||||
| URI: | http://repository.uki.ac.id/id/eprint/24143 |
Actions (login required)
![]() |
View Item |
