Sihotang, Sesilia Novi Aryanti (2024) Pengaruh Holding Time Pemanasan dan Holding Time Tempering pada Material Wire CHQ 10B21 Terhadap Kekerasan dan Struktur Mikro. S1 thesis, Universitas Kristen Indonesia.
![]() |
Text (Hal_Judul_Daftar_Isi_Daftar_Gambar_Daftar_Tabel_Daftar Lampiran_Abstrak)
HalJudulDaftarIsiDaftarGambarDaftarTabelDaftarDaftarSingkatanDaftarLampiranAbstrak.pdf Available under License Creative Commons Attribution Non-commercial Share Alike. Download (1MB) |
![]() |
Text (BAB I)
BABI.pdf Available under License Creative Commons Attribution Non-commercial Share Alike. Download (167kB) |
![]() |
Text (BAB II)
BABII.pdf Restricted to Registered users only Available under License Creative Commons Attribution Non-commercial Share Alike. Download (790kB) |
![]() |
Text (BAB III)
BABIII.pdf Restricted to Registered users only Available under License Creative Commons Attribution Non-commercial Share Alike. Download (712kB) |
![]() |
Text (BAB IV)
BABIV.pdf Restricted to Registered users only Available under License Creative Commons Attribution Non-commercial Share Alike. Download (1MB) |
![]() |
Text (BAB V)
BABV.pdf Restricted to Registered users only Available under License Creative Commons Attribution Non-commercial Share Alike. Download (69kB) |
![]() |
Text (Daftar Pustaka)
DaftarPustaka.pdf Available under License Creative Commons Attribution Non-commercial Share Alike. Download (206kB) |
Abstract
Studi ini menyelidiki pengaruh waktu penahanan selama pemanasan dan durasi temper terhadap kekerasan dan struktur mikro material wire CHQ 10B21, dengan fokus pada signifikansinya bagi industri baut. Melalui pengujian terkontrol yang pada variasi waktu penahanan 30 menit, 45 menit, 60 menit dan durasi temper selama 60 menit dan 75 menit, penelitian ini menganalisis sifat mekanis dan perubahan struktur mikro pada kawat CHQ 10B21. Penelitian dilakukan pada produksi baut yang diproduksi dari raw material wire CHQ 10B21 yang kemudian dipanaskan pada temperatur 870°C selama variasi waktu tertentu kemudian diquenching pada oli dan dilakukan tempering pada 480°C selama variasi waktu tertentu. Temuan penelitian menunjukkan adanya korelasi langsung antara waktu penahanan, durasi temper, kekerasan, dan struktur mikro. Hasil penelitian menunjukkan bahwa pada waktu tahan pemanasan lebih lama meningkatkan kekerasan dimana dengan pemanasan selama 60 menit menghasilkan kekerasan paling tinggi yaitu dari raw material sebelum pemanasan 14.0 HRC meningkat menjadi 29.0 HRC. Pula pada waktu tahan temper lebih lama akan meningkatkan keuletan material dimana dengan waktu tahan hardening 60 menit dan waktu temper 75 menit didapatkan nilai kuat tarik sebesar 891.91482 N/mm2. Untuk struktur mikro yang terbentuk pada semua perlakuan panas adalah martensite temper dan pada bagian ulir terlihat perbedaan morfologi pada area surface dan core. Penelitian ini memberikan wawasan berharga untuk mengoptimalkan proses perlakuan panas dan strategi pemilihan material dalam industri baut, yang pada akhirnya berkontribusi pada peningkatan kinerja dan efisiensi produk. Kata kunci: CHQ 10B21, perlakuan panas, waktu tahan hardening, waktu temper, baut. / This study investigates the influence of holding time during heating and tempering duration on the hardness and microstructure of CHQ 10B21 wire material, emphasizing its significance for the bolt industry. Through controlled experiments with varying holding times of 30 minutes, 45 minutes, and 60 minutes, and tempering durations of 60 minutes and 75 minutes, this research analyzes the mechanical properties and microstructural changes in CHQ 10B21 wire. The study was conducted on bolt products manufactured from CHQ 10B21 raw wire, which were then heated at 870°C for specific durations, quenched in oil, and tempered at 480°C for varying periods. The findings indicate a direct correlation between holding time, tempering duration, hardness, and microstructure. Results showed that longer heating holding times increased hardness, with a 60-minute heating duration resulting in the highest hardness increase from 14.0 HRC in the raw material to 29.0 HRC. Additionally, longer tempering durations enhanced material ductility, with a holding time of 60 minutes and a tempering duration of 75 minutes yielding a tensile strength of 891.91482 N/mm². The microstructure formed in all heat treatments was tempered martensite, with morphological differences observed between the surface and core areas of the threads. This study provides valuable insights for optimizing heat treatment processes and material selection strategies in the bolt industry, ultimately contributing to enhanced product performance and efficiency. Keywords: CHQ 10B21, heat treatment, hardening holding time, tempering duration, bolt.
Item Type: | Thesis (S1) | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Contributors: |
|
||||||||||||
Subjects: | TECHNOLOGY > Mechanical engineering and machinery | ||||||||||||
Divisions: | FAKULTAS TEKNIK > Teknik Mesin | ||||||||||||
Depositing User: | Sesilia Novi Aryanti Sihotang | ||||||||||||
Date Deposited: | 15 Jan 2025 08:37 | ||||||||||||
Last Modified: | 15 Jan 2025 08:37 | ||||||||||||
URI: | http://repository.uki.ac.id/id/eprint/17968 |
Actions (login required)
![]() |
View Item |